Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller:
Features:
1. The advanced 32-bit ARM CortexM4 high-performance processors, can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
Specifications:
Microprocessor
1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit
2. frequency: 168MHZ, 256K RAM
3.32 STM32F103 backup coprocessor
Sensor
1.L3GD20 3-axis digital gyroscope 16
2.LSM303D 3-axis accelerometer 14 / Magnetometer
3.MPU6000 6-axis accelerometer / magnetometer
4.MS5607 precision barometer
Interface
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
2312-920kv CW / CCW Motor :
Item: 2312
KV: 920kv
Stator Diameter 23.0 mm
Stator Thickness 12.0 mm
No. of Stator Arms 12
Magnet Poles 14
No-Load Current (Io/10V) 0.45 Amps
Motor Resistance (Rm) 0.117 Ohms
Max Continuous Current 14 Amps
Max Continuous Power 220 Watts
Outside Diameter 27.7 mm
Body Length 26 mm
Max Lipo Cell 2-4s
Suitable for: For DJI Phantom 1/2/3 F450/F550/S550 frame.
Suitable for propeller: For 9443 9450 1045 Self-locking propeller.
Features:
- Adopt integral motor shaft design, more effectively protect the motor shaft.
- A new type of impeller seat design is adopted, the performance is more stable, and the disassembly is more convenient.
- the load temperature is lower, the efficiency increase.
40A 2-4S ESC Specification:
BEC : 5V/3A
Li-ion/Li0poly:2-4S
Size: about 7.2x2.4cm (ESC with banana connector)
Weight: about 32g(with banana connector);
Note: This ESC is not able to flash the firmware.
Package Included:
1 x S550 PCB Quadcopter Frame Kit
6x 2312 920kv Motor
6 x 40A 2-4S ESC
4pairs 9450 Propeller
1 x Battery belt
1 x Low Voltage Buzzer Alarm
1 x Pixhawk 2.4.8 32bit ARM Flight Controller
1 x Safety button and Buzzer
1 x 4G TF card
1 x Shock Absorber
1 x Power module
1 x PPM wth shell
1 x I2C with shell
1 x RGB (There are two kinds of RGB module, send it at random.)
1 x Mini OSD
1 x M8N GPS
1 x GPS Holder
1 x 433Mh 100mW Telemetry Kit ( If you need 915Mhz Telemetry, you could leave a message for us when you place order )
Note :
Before you connect with computer , please make sure the SD card has been inserted to the flight controller first, and then flash the firmware , or it can not connected , also the led indicator will not light .
Please make sure you read these wikis and videos before you use.
https://www.youtube.com/watch?v=Hdhn0E1hEYc
https://www.youtube.com/watch?v=uH2iCRA9G7k
http://ardupilot.org/copter/docs/common-pixhawk-overview.htm